Design and Experiment of Transplanting Mechanism for High Density Vegetables with Small Plant Spacing
Abstract
Aiming at the problems of unreasonable trajectory, too large hole and poor uprightness of seedlings when the existing seedling planting mechanism is used for transplanting vegetables with small plant spacing, a Stephenson six-bar seedling planting mechanism suitable for transplanting vegetables with small plant spacing and high density was proposed. Firstly, the kinematics model of Stephenson six-bar seedling planting mechanism was established. Based on Visual Basic 6.0, the auxiliary analysis and optimization design software of seedling planting mechanism was developed. The influence of different mechanism parameters on seedling trajectory attitude was analyzed, and a set of satisfactory mechanism parameters were obtained by optimizing human-computer interaction. Secondly, the structural design of the seedling planting mechanism was carried out. The three-dimensional modeling and virtual prototype simulation were carried out. The test bench was built and the idle test was carried out to obtain the actual seedling planting trajectory. The theoretical trajectory, virtual simulation trajectory and actual seedling planting trajectory were compared. The three trajectories were basically the same, which verified the rationality of the design of the seedling planting mechanism. Finally, the seedling planting test was carried out. When the seedling planting test was carried out at different speeds of 20~40r/min, the average qualified rate of seedling planting was 91.7%. After transplanting, the seedling spacing was controlled at about 110mm, and the verticality was close to 90°, which met the requirements of small spacing and high density transplanting, and verified that the seedling planting mechanism had good feasibility and practicability.
Keywords: vegetable seedling planting mechanism, small plant spacing, high density transplanting, human computer interaction, virtual simulation, seedling planting test
Download Full Text:
PDFReferences
ZHOU Meifang,YU Gaohong,ZHAO Yun,et al. Parameter optimization and test on pick-up mechanism of planetary gear train with ellipse gears for vegetable plug seedling[ J ]. Transactions of the CSAE ,2014 ,30( 18) ;13 -21. (in Chinese)
LIU Cunxiang,LI Xiaohu,YUE Xiuman, et al. Current situation and development trend of dry land transplanters in China [J ]. Journal of Agricultural Mechanization Research, 2012,37(6) *.249 -252. (in Chinese)
XIN Zhulin, CUI Yanjuan, YANG Xiaowei, et al. Current situation of global vegetable industry and research progress of vegetable breeding development path in China J ]. Molecular Plant Breeding ,2022 ,20 (9 ) ; 3122 - 3132. (in Chinese)
DING Haifeng,FAN Jianguang, JIA Changcai, et al. Development status and trend of vegetable seed industry in China [ J ]. Chinese Vegetables,2020(9) ;1 -8. (in Chinese)
GAO Fang, LI Hongchang. Research on the impact of vegetable mechanization on seedling quality [ J]. Journal of Agricultural Mechanization Research ,2018 ,40 ( 12) ; 125 - 129. (in Chinese)
ZHOU Fujun.LU Jie.DU Jiaxing. Parameter optimization and experiment of disc-type planting mechanism for corn bowl seedling transplanter [ J ]. Transactions of the CSAE ,2014 ,30 ( 1 ) : 18 -24. (in Chinese)
TATSUYA K, KOHNOSUKE T, MUNEKI T, et al. Developement of zigzag planting mechanism for rice transplanter [J]. Journal of the Japanese Society of Agricultural Machinery, 1999 ,61 ( 1 ) : 179 - 185.
BREWER II L. Conceptual modeling automated seeding transfer from growing trays to shipping modulus [J ]. Transactions of the ASAE,1994,37(4) :1043 - 1051.
HASSAN A E, HADDOCK W H. Packing of pine seedlings using soil failure criteria [J ]. Transactions of the ASAE, 1991 ,34 (2) : 695 -698.
JIN X, LI S J, YANG X J, et al. Developments in researc h on seedling auto-pirking device of vegetable transplanter [ J ]. Applied Mechanics & Materials,2013 ,364 ;375 -379.
SATPATHMY S K, GARG I K. Effect of selected parameters on the performance of a semi-automatic vegetable transplanter [J]. Agricultural Mechanization in Asia, Africa and Latin America ,2008 ,39 (2) ;47 —51.
XUE X, LI L, XU C, et al. Optimized design and experiment of a fully automated potted cotton seedling transplanting mechanism [ J ]. International Journal of Agricultural and Biological Engineering,2020 ,13 (4) : 1 1 1 — 117.
BAE К Y, YANG Y S. Design of a non-circular planetary-gear-train system to generate an optimal trajectory in a rice transplanted [J ]. Journal of Engineering Design,2007 ,18(4) ; 361 -372.
CHEN Jianneng, HUANG Qianze,WANG Ying, et al. Kinematic modeling and analysis of seedling planting mechanism of elliptic gear planetary system of pot seedling transplanter [J ]. Transactions of the CSAE, 2012,28(5) ;6 - 12. (in Chinese)
CHEN Jianneng, HUANG Qianze, WANG Ying, et al. Parametric analysis and inversion of transplanting mechanism with planetar)' non-circular gears for potted-seedling transplanter [ J ]. Transactions of the CSAE, 2013,29 ( 8 ): 18 - 26. (in Chinese)
CHI Minglu,LI Xuving,TIAN Yang,et al. A study on the adjustment of the planting distance of the hanging cup transplanter [J ]. Journal of Agricultural Mechanization Research ,2014 ,36 ( 2 ) : 131 - 134. (in Chinese)
HU Jianping, PAN Jie, ZHANG Chendi, et al. Optimal design and experiment of planetary gear planting mechanism [ J ]. Transactions of the Chinese Society for Agricultural Machinery ,201 8 ,49 ( 1 1 ) ;78 -86. (in Chinese)
YU Gaohong,LIAO Zhenpiao,XU Lehui, et al. Optimization design and test of large spacing planetary gear train for vegetable pot-seedling planting mechanism [ J ]. Transactions of the Chinese Society for Agricultural Machinery, 2015,46(7) : 38 -44. ( in Chinese)
Refbacks
- There are currently no refbacks.
